Doors are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.

Panels are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.

Type F/C -Floor to Ceiling Pilasters are 1-1/4” thick, constructed with two 18-gauge sheets of commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. Edges are then interlocked with a continuous roll-formed edge molding. An inverted heavy gauge channel shall be welded into top and bottom of the pilaster for additional reinforcing. Pilasters are attached to finished floor and ceiling with angle brackets. A polished 3” high stainless steel shoe of one-piece construction shall be supplied to conceal the floor and ceiling anchoring. Tamper proof shoe assembly held in place by means of concealed floor anchor clips –exposed screws are not acceptable. 

Powder coated finishes are applied over diamond textured electro-galvanized steel containing a zinc coating thickness of .00015”. All components shall be cleaned and degreased prior to application of powder for maximum finish adhesion. A hybrid epoxy/polyester powder is then applied by an electrostatic painting system to ensure uniform thickness. Baking at 345 degrees for 22 minutes cures the finish. 

Shall be selected from AAMCO’s standard range of color offerings.

All material components are fully prepared with suitable internal reinforcement to receive all necessary hardware and fittings. AAMCO supplies factory pre-drilled components for a safer, more efficient and trouble-free installation. All door hinges and strike/keeper will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings have a corrosion resistant finish.

Doors:

-Upper and lower door brackets are heavy non-ferrous Zamac castings that become integral part of door as they are imbedded within pre-formed abscesses at time of assembly. Powder coated finish shall match selected door color.

-Top hinge bracket (#102) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.

-Stainless steel 5/16” diameter pin (#101) goes through the door and the top hinge bracket for three-point bearing.

-Bottom hinge bracket (#103) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.

-Concealed latch assembly with stainless steel pin allows for emergency access. Cover plate and turn knob (#104) are heavy, non-ferrous Zamac castings with chrome plated finish. ADA lever handles are supplied on all handicap doors.

-Door strike and keeper (#105) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.

-Combination coat hook and bumper (#106) is a heavy, non-ferrous Zamac casting with chrome-plated finish.

Wall and Pilaster Brackets:

-Shall be heavy, non-ferrous Zamac castings with chrome-plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets. 

Shall be in accordance with AAMCO’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Actual pilaster length is determined by ceiling height.

 AAMCO provides for all diamond textured powder coated materials, when properly maintained, a one-year warranty against all defects in workmanship and construction under normal wear and use of this product.

Shall be selected from AAMCO’s standard range of color offerings.

All doors to be 1” thick by 55” high - All edges machine finished w/ ¼” radius

All panels to be 1” thick by 55” high - All edges machine finished w/ ¼” radius

All pilasters to be 1” thick - All edges machine finished w/ ¼” radius >>Note!- Maximum Ceiling Height = 10’-0” (120”)

All shoes at floor to be 3” high fabricated from 20 gauge type 304 stainless steel w/#4 finish OR one-piece molded plastic

All shoes at ceiling to be 4” high fabricated from 20 gauge type 304 stainless steel w/ #4 finish

All brackets to be 54” high and made of extruded PVC plastic (color to match panels) OR 1 ½” stirrup type brackets made from extruded aluminum w/ clear anodized finish (3 per connection)

All fasteners to be stainless steel tamper proof security type screws. 

Toilet partitions shall be constructed of high-density polyethylene (HDPE) resins. Partitions shall have homogenous color throughout with uniformly machined 0.25” radius edges. All plastic components to arrive with a protective plastic masking

Shall be selected from AAMCO’s standard range of color offerings.

HINGES:

-Doors are fabricated with an integral hinge system consisting of a pilaster machined to accept a door and hinge mechanism with no exposed metal parts.

-Integral hinges consist of a two piece cammed nylon pin at bottom of door and one 4” nylon pin at the top of door. Nylon pins are secured in place with stainless steel pins.

-Alternate hinges to be 8” high wrap around type made from extruded aluminum w/ clear anodized finish. Hinges are designed for easy adjustment in the field to either a fully closed or partially opened position.

DOOR HARDWARE:

-Strike/keeper to be a heavy duty 6” high clear anodized aluminum extrusion with sound dampening rubber insert. ADA compliant slide latch to be clear anodized aluminum with a black anodized sliding insert.

-Slide latch to be equipped with angle bar for emergency access.

-Each door to be supplied with one chrome plated zamac coat hook with bumper.

-Each handicap door shall be supplied with one chrome plated zamac pull handle.

Shall be in accordance with AAMCO’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 54” high and mounted 12” above finished floor. Actual pilaster length is determined by ceiling height.

All American guarantees solid plastic material against breakage, corrosion, and delamination for a period of fifteen (15) years. If materials are found defective during this period for any of the reasons listed above, the materials will be replaced free of charge. Warranty does not included installation errors, improper usage, or vandalism.

Doors are 1” thick, constructed with two 22-gauge sheets of stretcher leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous stainless steel roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.

Panels are 1” thick, constructed with two 22-gauge sheets of stretcher leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous stainless steel roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.

Type F/C -Floor to Ceiling Pilasters are 1-1/4” thick, constructed with two 18-gauge sheets of stretcher leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. Edges are then interlocked with a continuous stainless steel roll-formed edge molding. An inverted heavy gauge channel shall be welded into top and bottom of the pilaster for additional reinforcing. Pilasters are attached to finished floor and ceiling with stainless steel angle brackets. A polished 3” high stainless steel shoe of one-piece construction shall be supplied to conceal the floor and ceiling anchoring. Tamper proof shoe assembly held in place by means of concealed floor anchor clips –exposed screws are not acceptable.

All doors, panels and pilasters shall be type 304 stainless steel with a #4 finish and include a durable plastic film covering to safeguard them during shipment and installation. All components shall have vertical grain finish except panels wider than 58-1/2”, seaming is not acceptable. 

Shall be selected from AAMCO’s standard range of color offerings.

All material components are fully prepared with suitable internal reinforcement to receive all necessary hardware and fittings. AAMCO supplies factory pre-drilled components for a safer, more efficient and trouble-free installation. All door hinges and strike/keeper will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings have a corrosion resistant finish.

Doors:

-Upper and lower door brackets are stainless steel castings that become integral part of door as they are imbedded within pre-formed abscesses at time of assembly. Satin finish shall closely resemble door finish.

-Top hinge bracket (#102) is a heavy, non-ferrous Zamac casting with chrome plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.

-Stainless steel 5/16” diameter pin (#101) goes through the door and the top hinge bracket for three-point bearing.

-Bottom hinge bracket (#103) is a heavy, non-ferrous Zamac casting with chrome plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.

-Concealed latch assembly with stainless steel pin allows for emergency access. Cover plate and turn knob (#104) are heavy, non-ferrous Zamac castings. ADA lever handles are supplied on all handicap doors.

-Door strike and keeper (#105) is a heavy, non-ferrous Zamac casting with chrome plated finish One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.

-Combination coat hook and bumper (#106) is a heavy, non-ferrous Zamac casting with chrome plated finish.

Wall and Pilaster Brackets:

-Shall be heavy, non-ferrous Zamac castings with chrome plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets. 

Shall be in accordance with AAMCO’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Actual pilaster length is determined by ceiling height. 

AAMCO provides for all stainless steel materials, when properly maintained, a ten-year warranty against all defects in workmanship and construction under normal wear and use of this product. 

Shall be selected from AAMCO’s standard range of color offerings.